• Toyota+HDJ78+-+HDJ79+-+HZJ79+Series+Landcruiser+Front+Mount+Intercooler+Kit+std+intake
  • PDI+Landcruiser+HDJ79+Front+mount+Intercooler+Hole+in+panel
  • HDJ79+PDI+front+mount+intercooler+blacked+out+front
  • PDI+Landcruiser+HDJ79+Front+mount+Intercooler+Core+with+grill+RHS
  • PDI+Landcruiser+HDJ79+Front+Mount+intercooler+PDI+core+no+grill
  • PDI+Landcruiser+HDJ79+Front+Mount+intercooler+RHS+through+front+support
  • PDI+Landcruiser+HDJ79+Front+mount+Intercooler+Core+with+grill+LHS

Landcruiser 75 Series Front Mount intercooler Kit HZJ75 / HJ75 / Early narrow nose models

$1,710$1,845

Description

Landcruiser 75 Series Front Mount intercooler Kit HZJ75 / HJ75 / Early narrow nose models

 

The PDI Landcruiser HDJ79 Front Mount intercooler kit is the neatest and most effective intercooler kits to suit your 73, 75 or 77 series narrow nose cruiser.

The PDI Landcruiser 75 Series Front Mount intercooler kit for the 6 cylinder narrow nose 70 series sits directly behind the factory grill for maximum cooling potential and will not interfere with other installed items such as lights or a winch. This is possible with the relocation of air conditioner piping and the drier to the engine bay.

All parts required to mount the intercooler and relocate the intercooler are included in the kit. This includes three flexible hoses and the drier for moving the air conditioner piping from behind the grill.

Long term testing has shown this to be highly effective for the inlet air temperatures and for the function of the air conditioner itself with no impact on the radiators ability to keep the engine cool.

The cores are 600mm x 240mm x 65mm, which fills the space available at the front. Our front mount kit cooling capability is greater than all other kits we have tested so the improvements in torque and power will exceed other results. PDI kits use moulded end tanks to get maximum width.

We limit the height to the grill opening and stay away from extending the core down to sit both behind the front panel and/or in front of the horizontal crossmember, which means cooling flow isn’t restricted. Other kits, which don’t get the same unrestricted flow, would expect to see dilution of the chilled air with air that hasn’t been able to be effectively cooled therefore becoming less efficient. Customers and tuners are amazed how well our PDI systems work. Being neat, as per factory finish, adds to the appeal.

Once fitted are a zero maintenance setup, and still allow access into the engine bay for any maintenance or inspection.

For those with factory turbo engines (1HDFTE standard or converted to 1HDT or 1HDFT) we have 76mm cores. Black cores are available, black piping is not standard.

 

 

 

MORE INFORMATION BELOW

 

Initial testing of the system was with an upgraded Gturbo Badboy turbo, tuning module, Safari ARMax snorkel and running standard injectors and standard airbox.  Dyno testing with this configuration has resulted in a max power of 186.4kW at the wheels with a low 20psi boost.  We also managed to achieve 18psi at 1550rpm with maximum torque of 668Nm at (only) 1850rpm. There is no doubt this is has to be one of the best combinations for a “mildly modified” 1HDFTE that boasts only 122kW at the engine (100rwkw) in factory form.

Our next step was to install +30% injectors. There is a step change in performance with this upgrade and needs a retune.  With a few changes we managed to get 246rwkw (330hp at the wheels) and 900nm so an excellent result.

The test setup is running +70% injectors and has 311rwkw and over 1000nm. The 76mm core will make that even easier, with larger end tanks and better internal flow for high boost.

To make space for the intercooler core, the air conditioner piping has to be rerouted.  The components to do this are included in the kit and the task is simple enough.  Spacers are provided to space the radiator back at the top.  Then the condenser has a few spacers and longer bolts to allow that to also be pushed back so that nothing touches.  The condenser stays in place and flexible lines take care of the rest of the relocating. Initial testing on two different cruisers resulted in the fitter doing the regassing comment on how well the system was performing.  With the installation of the core up front it continues to work really well – on a hot day it is the place to be.

With the ambient temperature 33-37deg a heavy tandem axle trailer was hitched up to increase load.

                                                     Post turbo inlet             Post intercooler inlet temperatures

Normal around town driving            50-150degC     42-46degC

Highway normal driving (towing)    90-160degC                     48-52degC

Max load up long hill                         180degC                           60degC

Under full load thats 36% more air going into the engine, which will result in a significantly improved EGT with the same fuel or add more fuel to make even more power. For those running standard injectors this is an excellent improvement. All these results were using a 500mm wide core.

We have done some more testing of the current 600mm wide core now that we can apply more load.

When working hard the turbo outlet temp was pushed to 260degC and post intercooler temps were down to 70degC – a 190degC reduction.  The results below show how effective the PDI front mount is compared to top mounted configuration.

Compare this to one of the mid size current top mount setups that had turbo outlet temp of 130degC and post intercooler temp of 90degC – a 40degC reduction.  We have tested the largest top mount offering and with around 150rwkw the post turbo temp was up to 190degC and the post intercooler temp was 75degC – a 115degC reduction.

Further testing with the high flow injectors has seen the intake temperatures pulled down from 250-260degC to 70 degC on a 28degC day.  That is significant.  A top mount under the same conditions is expected to be no better than 140degC.

If you’re looking here then you’ve probably worked out that our front mounts will out perform any top mount intercoolers.

Next thing is to work out what differentiates PDI from other front mount options.

Bonnet latch is support with solid steel brackets from lower crossmember.  We do not use the intercooler to absorb the shocks of bonnet bounce.

We maximise the size of the core behind the grill opening and have been seeing results far more impressive than the smaller core should be producing.  Our custom cast end tanks were designed to give us maximum width.  While it is possible to make the core taller by going down further, an examination of the space will show that a 40mm portion of the extended core is blocked off from behind by the crossmember.  The area that goes below the crossmember is then also blocked from the front by the lower painted panel and additionally it is unlikely to have any cooling from the air being pulled by the fan from behind.  This portion of intercooler which does not see the same cooling as the upper part can have the affect of diluting the air charge with air that has not been cooled as much and therefore.

Cast end tanks are used as airflow will be smoother, especially while going between the tank and welded pipe.  No welds means a stronger tank that won’t bust open along the seems at high boost.

We have chosen to go through the front panel down low as this is the simplest penetration (with an existing hole 38mm diameter) and has limited impact on the structure.  The 75/79 series six cylinder radiator is mainly supported from the top mount so strength here is important.

We have seen custom installs that may look great, but no only do they go through next to the radiator mounts, they also cut away a large portion of the lower crossmember, which is a major structural component. For these custom setups, although the rear of the crossmember is kept, there is no flow through a 50mm horizontal section of the core as it is blocked from the front and the back.

Our stainless pipework is all one piece with no welding.  The stainless routing goes over and points down at the turbo outlet so we can use a straight connection in silicon. This routing also works with a range of airboxes including factory, Moonlight and our soon to be released PDI airbox.

The fact that a factory grill can be modified to fit over our intercooler is great.  It means you don’t have to work out what colour to paint the intercooler core or custom grill so it looks like a Landcruiser.

Additional information

Kit Option

1HZ turbo HZJ79/HZJ75/HZJ77, HJ75 with 2H/12HT, HZJ75/77/narrow nose with ?? engine – contact us for options

THE GTURBO PROMISE

Experience the performance of a GTurbo

  • UP TO 150%

    Increase in Power
  • 50%-200%

    Increase in Torque
  • 2%-10%

    Increase in Fuel Economy

SUPPORT

Need Help?

43.3k

Feed the need

Join our growing community on instagram.

0
    Your cart is emptyReturn to Shop